Dometic 9200 Awning Arm Kit | 8962002.400UL | Standard | Bottom Wire | Set

Restore or replace worn awning arm hardware with the Dometic A&E 9200 Power Awning Arm Hardware Kit — Standard Pitch, BOTTOM WIRE EXIT (Part #8962002.400UL, Black). Complete LEFT + RIGHT arm set specifically for Dometic 9200 Power Awnings — the standard-pitch geometry version in black finish. Includes gas strut support and adjustable pitch on both arms.

⚠️ 9200-Specific Kit — Not for 9100 Systems

This kit is engineered specifically for Dometic 9200 Power Awning systems and their compatible 925, 926, and 927 Series awning tubes. If your awning system is a 9100 series (with 915, 917, or 910 tubes), you'll need the 9100-specific version:

• Dometic 8952002.400UL — 9100 Standard Pitch Bottom Wire Kit (Black)
• Dometic 8952002.400BL — 9100 Standard Pitch Bottom Wire Kit (White)

Verify your awning series before ordering.

⚠️ Complete LEFT + RIGHT Set

This kit includes both the left and right awning arms as a matched pair. Right choice for buyers doing complete hardware replacement or upgrade.

⚠️ BOTTOM WIRE EXIT — Critical Fitment Detail

This arm set is specifically the BOTTOM WIRE EXIT variant. Verify your existing installation's wire exit direction before ordering:

• Wire exits from the BOTTOM of the arm → this 8962002.400UL is the correct match (this listing)
• Wire exits from the TOP of the arm → different arm set required

The wire exit direction is fixed on the arm architecture — you can't reroute wiring to match a mismatched arm.

Standard Pitch Style

The standard-pitch style is the most widely used awning arm geometry — includes standard lengths for both back and front channels with a standard pivot point that produces a 13-1/4" drop of the awning when extended.

If your existing awning has the shallower reduced-pitch geometry (2" drop), you'll need a different arm variant.

Compatibility

Compatible with:

• Dometic 9200 Series Fabric Roller Tube Assemblies
• 925, 926, and 927 Series Awning Tubes

The Workhorse of Your Awning System

Extension arms are a crucial component of the awning system:

• Mount to your RV sidewall and extend outward
• Support the fabric roller tube assembly
• Provide tension to keep fabric taut and stable
• Support fabric weight — prevent sagging and flapping in the wind
• Provide a stable base for shade and weather protection

Gas Strut Support (Both Arms)

Both arms in the set are equipped with a gas strut that creates and maintains tension on the awning when extended — keeping it stable even in breezy conditions. The struts also distribute fabric weight and reduce stress on the arms and your RV's sidewall.

Adjustable Pitch (Both Arms)

Both arms include adjustable pitch for fine-tuning the angle:

• Loosen the knob on each adjustable arm
• Move each arm up or down to change the awning angle
• Tighten the knobs to secure both arms in place

Better sun protection in early morning or late afternoon, plus prevents rainwater pooling on the fabric.

Physical Specifications (Per Arm)

• Back Channel Length: 65-5/8"
• Front Channel Length: 64-7/8"
• Lower Pivot Height: 30-5/16"
• Projection with Awning: 91-1/2"
• Extension Pitch Drop: 13-1/4"

Important Notes About Hardware Finish & Construction

Dometic uses two different painter suppliers, which means hardware finish may appear glossy, matte, or even a mix of both within the same hardware set (left and right arm). Dometic does not consider this variation a defect and does not offer exchanges or alternatives based on finish appearance.

The hardware back channel may have a slight bow due to the manufacturing process. This is not a defect — upon installation, the hardware will sit flat against the RV. The awning arm is intentionally engineered to be lightweight and to rely on the strength of your RV's sidewall for support.

Key Features

• Genuine Dometic A&E OEM awning arm hardware kit for 9200 Power Awnings
• 9200-specific — for 925/926/927 series awning tubes (NOT for 9100 systems)
• Complete LEFT + RIGHT set — matched pair
• BOTTOM WIRE EXIT variant — critical fitment differentiator
• Standard pitch style — 13-1/4" drop when extended
• Gas strut support on both arms for tension and stability
• Adjustable pitch on both arms for sun/rain angle control
• Black finish

Specifications

• Brand: Dometic (A&E)
• Part Number: 8962002.400UL
• Type: RV Power Awning Arm Hardware Kit (LEFT + RIGHT set)
• Awning Series: 9200
• Style: Standard Pitch
• Wire Exit: BOTTOM
• Color: Black
• Features: Gas strut support (both arms), adjustable pitch (both arms)
• Compatible With: Dometic 9200 Series Fabric Roller Tube Assemblies; 925, 926, 927 Series Awning Tubes
• NOT Compatible With: Dometic 9100 systems (use 8952002.400UL/BL instead)
• Back Channel Length (per arm): 65-5/8"
• Front Channel Length (per arm): 64-7/8"
• Lower Pivot Height: 30-5/16"
• Projection with Awning: 91-1/2"
• Extension Pitch Drop: 13-1/4"
• Includes: Left arm, right arm (complete pair set)